Opel Vectra B

since 1995 of release

Repair and car operation



Vektr B. Opel
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
- 9. Running gear
   9.1. Introduction
   9.2. Technical characteristics
   9.3. Rotary fists
   9.4. Replacement of forward bearings of a nave
   9.5. Forward bottom frame
   9.6. The lobby is resistant
   9.7. Stabilizer of cross-section stability of a forward suspension bracket
   9.8. Bottom lever of a forward suspension bracket
   9.9. Replacement of the bottom hinge of a forward suspension bracket
   9.10. Back nave
   9.11. Back rack
   9.12. Stabilizer of cross-section stability of a back suspension bracket
   9.13. Top lever of a back suspension bracket
   9.14. Bottom lever of a back suspension bracket
   9.15. Steering wheel
   9.16. Steering column
   9.17. Intermediate shaft of a steering column
   9.18. Replacement of protective covers of steering transfer
   9.19. Steering transfer
   + 9.20. Pump of the amplifier of a steering
   9.21. Air removal from steering system with the amplifier
   9.22. Tip of steering draft
   9.23. Steering draft
   9.24. Corners of installation of wheels
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions


5645d6d1

9.6. The lobby is resistant

GENERAL INFORMATION

Details of a forward rack

Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports. Remove the corresponding forward wheel.
2. Unscrew a nut and disconnect draft of the stabilizer of cross-section stability for a forward rack.
3. Disconnect a brake hose from an arm on a forward rack.
4. Disconnect wires of the sensor of wear of brake shoes from a forward rack.
5. Note the provision of a rack on a rotary fist.
6. Unscrew two bolts of fastening of a rotary fist to a forward rack.
7. Unscrew bolts of fastening of a rotary fist to a forward rack.
8. Take a bolt of fastening of a rotary fist to a forward rack.
9. Take the top part of a rotary fist from a rack and establish a rotary fist on a support.
10. In a motor compartment remove a protective plastic cap from the top part of a forward rack.
11. Unscrew a nut of fastening of the top part of a rack. Thus hold a rod of a forward rack from a provorachivaniye a wrench.
12. Remove a nut of fastening of the top part of a forward rack.
13. Remove the top support of a forward rack.
14. Lower a rack and take from under a forward wing.

Repair of a forward rack

The forward rack which has been removed from the car


PERFORMANCE ORDER
1. Using the special adaptation, compress a spring so that it departed from the top part. When using the special adaptation for compression of springs watch, that rounds of a spring were reliably grasped and compression of a spring make from the opposite sides.

Prevention

The spring has very big effort of compression therefore use only very reliable tool. At all do not connect a spring a wire.


2. Fix a key a shock-absorber rod from a provorachivaniye and, using the second cap key, unscrew the central nut of fastening of a rod of the shock-absorber.
3. Remove the top ring with the bearing.
4. Remove top гнедо springs.
5. Remove the buffer.
6. Remove a spring from a forward rack.
7. Check all elements of a forward rack on wear, damages or deformation. Check smoothness of a course of a rod of the shock-absorber. Check the shock-absorber on tightness, and also its rod on dot corrosion on all length.
8. Establish a cylindrical spring so that its bottom end correctly settled down in the bottom nest of a spring.
9. Establish the buffer, top гнедо springs and the top ring with the bearing.
10. Screw a nut on a rod of the shock-absorber and tighten it the demanded moment, thus hold a rod from a provorachivaniye the second wrench.
11. Slowly weaken the tool for spring compression. Check that extreme rounds of a spring correctly settled down in spring nests.

Installation

Installation is made in sequence, return to removal.