Opel Vectra B

since 1995 of release

Repair and car operation



Vektr B. Opel
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
- 9. Running gear
   9.1. Introduction
   9.2. Technical characteristics
   9.3. Rotary fists
   9.4. Replacement of forward bearings of a nave
   9.5. Forward bottom frame
   9.6. The lobby is resistant
   9.7. Stabilizer of cross-section stability of a forward suspension bracket
   9.8. Bottom lever of a forward suspension bracket
   9.9. Replacement of the bottom hinge of a forward suspension bracket
   9.10. Back nave
   9.11. Back rack
   9.12. Stabilizer of cross-section stability of a back suspension bracket
   9.13. Top lever of a back suspension bracket
   9.14. Bottom lever of a back suspension bracket
   9.15. Steering wheel
   9.16. Steering column
   9.17. Intermediate shaft of a steering column
   9.18. Replacement of protective covers of steering transfer
   9.19. Steering transfer
   + 9.20. Pump of the amplifier of a steering
   9.21. Air removal from steering system with the amplifier
   9.22. Tip of steering draft
   9.23. Steering draft
   9.24. Corners of installation of wheels
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions





9.3. Rotary fists

GENERAL INFORMATION

Prevention

At installation of a rotary fist it is necessary to use all new bolts and nuts.


Nave and rotary fist

Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports. Remove the corresponding forward wheel.
2. Unscrew a nut of fastening of steering bent for to a rotary fist. Using a stripper, take the spherical hinge of steering draft from a rotary fist.
3. Unscrew tightening a bolt, the fixing spherical hinge of the bottom lever of a forward suspension bracket to a rotary fist.
4. Using the lever, move the bottom lever of a forward suspension bracket down and take the spherical hinge from a rotary fist. If the pin of the spherical hinge densely sits in a rotary fist, use a screw-driver or a thin chisel as a wedge and expand a clip of fastening of a pin of the spherical hinge.
5. Remove a support, without disconnecting from it a brake hose. Using a soft wire, suspend a support on a forward rack.
6. Unscrew a bolt and remove the sensor of speed of a wheel.
7. Remove a cap of a nut of a nave, take a pin and unscrew a nut of fastening of a power shaft to a nave.
8. Take a power shaft to a nave, taking away a rotary fist from the car.
9. Note the provision of a rack of a forward suspension bracket on a rotary fist.
10. Unscrew two bolts of fastening of a rack of a forward suspension bracket to a rotary fist. Thus finally take a power shaft from a rotary fist.
11. Remove a rotary fist.
12. Unscrew the screw and remove a forward brake disk from a nave flange.
13. Unscrew screws (shooters) and remove a mudguard from a rotary fist.

Installation

PERFORMANCE ORDER
1. Establish a mudguard on a rotary fist and fix screws.
2. Establish a brake disk.
3. Check that shlitsa on the external end of a power shaft and grooves in a nave the pure. Pull a nave over grooves of a power shaft.
4. Pull a rotary fist over a power shaft. Arrange the top part of a rotary fist on a rack and fix bolts.
5. Screw a nut of fastening of a power shaft to a nave and tighten it the demanded moment.
6. Establish a support of brakes.
7. Establish a pin of the spherical hinge of the bottom lever of a forward suspension bracket in a rotary fist and fix tightening a bolt.
8. Establish steering draft.
9. Establish a wheel and lower the car.
10. In some stages tighten a nut of fastening of a power shaft to a nave and fix it a pin.
11. Establish a cap of a nut of fastening of a power shaft to a nave.
12. Check and, if necessary, adjust corners of installation of wheels.