Opel Vectra B

since 1995 of release

Repair and car operation



Vektr B. Opel
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
- 9. Running gear
   9.1. Introduction
   9.2. Technical characteristics
   9.3. Rotary fists
   9.4. Replacement of forward bearings of a nave
   9.5. Forward bottom frame
   9.6. The lobby is resistant
   9.7. Stabilizer of cross-section stability of a forward suspension bracket
   9.8. Bottom lever of a forward suspension bracket
   9.9. Replacement of the bottom hinge of a forward suspension bracket
   9.10. Back nave
   9.11. Back rack
   9.12. Stabilizer of cross-section stability of a back suspension bracket
   9.13. Top lever of a back suspension bracket
   9.14. Bottom lever of a back suspension bracket
   9.15. Steering wheel
   9.16. Steering column
   9.17. Intermediate shaft of a steering column
   9.18. Replacement of protective covers of steering transfer
   9.19. Steering transfer
   + 9.20. Pump of the amplifier of a steering
   9.21. Air removal from steering system with the amplifier
   9.22. Tip of steering draft
   9.23. Steering draft
   9.24. Corners of installation of wheels
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions


5645d6d1

9.11. Back rack

GENERAL INFORMATION

Back rack

Removal

PERFORMANCE ORDER
1. Lift a back part of the car and fix on supports. Remove the corresponding back wheel. Establish a back beam on a support.
2. Remove the protective loose leaf from under an arch of a back wheel.
3. Unscrew a back bolt of fastening of the top part of a back rack.
4. Unscrew a forward bolt of fastening of the top part of a back rack.
5. Take a rack from under a wheel arch.

Repair

Arrangement of a bolt of fastening of a fixing element of a back rack


PERFORMANCE ORDER
1. Using the special adaptation, compress a spring so that its top cup unloaded.
2. Fix from a provorachivaniye a shock-absorber rod a key and, using the second key, unscrew a nut of fastening of a rod of the shock-absorber.
3. Remove a nut of fastening of a rod of the shock-absorber.
4. Remove from a shock-absorber rod the top plate.
5. Remove a dempfiruyushchy ring.
6. Remove a fixing element.
7. Remove the plug.
8. Remove a glass.
9. Remove the buffer and a cylindrical spring.
10. Remove a spring nest from a fixing element of a back rack.
11. Check all elements of an amortization rack on wear, damages or deformation. Check smoothness of a course of a rod of the shock-absorber. Check the shock-absorber on tightness, and also its rod on dot corrosion on all length.
12. Establish top гнедо springs in a fixing element of a back rack.
13. Establish on a shock-absorber rod the buffer, a glass and the plug.
14. Establish a fixing element of a back rack on a cylindrical spring, and the end of a spring should settle down in dredging of the top oppression of a spring (shooter).
15. Establish a dempfiruyushchy ring and the top plate.
16. Screw up a nut of fastening of a rod of the shock-absorber, thus hold a rod from a provorachivaniye a wrench.
17. Slowly weaken the special tool for spring compression.

Installation

PERFORMANCE ORDER
Installation is made in sequence, return to removal. Tighten bolts of fastening of a fixing element of the top part of a back rack after car installation on wheels.