Opel Vectra B

since 1995 of release

Repair and car operation



Vektr B. Opel
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
- 9. Running gear
   9.1. Introduction
   9.2. Technical characteristics
   9.3. Rotary fists
   9.4. Replacement of forward bearings of a nave
   9.5. Forward bottom frame
   9.6. The lobby is resistant
   9.7. Stabilizer of cross-section stability of a forward suspension bracket
   9.8. Bottom lever of a forward suspension bracket
   9.9. Replacement of the bottom hinge of a forward suspension bracket
   9.10. Back nave
   9.11. Back rack
   9.12. Stabilizer of cross-section stability of a back suspension bracket
   9.13. Top lever of a back suspension bracket
   9.14. Bottom lever of a back suspension bracket
   9.15. Steering wheel
   9.16. Steering column
   9.17. Intermediate shaft of a steering column
   9.18. Replacement of protective covers of steering transfer
   9.19. Steering transfer
   + 9.20. Pump of the amplifier of a steering
   9.21. Air removal from steering system with the amplifier
   9.22. Tip of steering draft
   9.23. Steering draft
   9.24. Corners of installation of wheels
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions


5645d6d1

9.15. Steering wheel

MODELS WITHOUT THE SAFETY CUSHION

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Establish forward wheels for movement directly forward.
3. Remove the button of a sound signal from a steering wheel and disconnect the electric socket.
4. A screw-driver unbend a short mustache of fixing of a nut of fastening of a steering wheel
5. Unscrew a nut of fastening of a steering wheel.
6. Put labels of combination of a steering wheel and a steering shaft.
7. Using a stripper, remove a steering wheel and a spring from a steering shaft.
8. Establish a spring and a steering wheel on a shlitsa of a steering shaft. Thus combine the labels made at removal of a steering wheel.
9. Establish a new spring washer and screw a nut of fastening of a steering wheel, having tightened it the demanded moment.
10. A screw-driver unbend a short mustache of fixing of a nut of fastening of a steering wheel.
11. Connect the electric socket to the button of a sound signal and establish the button in the center of a steering wheel.
12. Connect the accumulator and check action of a sound signal.

MODELS WITH THE SAFETY CUSHION

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
Prevention

Further actions make not earlier than in 1 minute that the condenser of an airbag was discharged completely.


2. Establish forward wheels for movement directly forward.
3. Unscrew two screws from a back part of a steering wheel.
4. Being careful, remove a safety airbag.
5. Disconnect the electric socket from a safety cushion.
6. At existence disconnect the electric socket from the switch of management of a radio receiver.
7. A screw-driver unbend a short mustache of fixing of a nut of fastening of a steering wheel. Completely unscrew bolts of fastening of a wheel and remove a wheel.
8. Unscrew and remove a nut of fastening of a steering wheel.
9. Remove a spring washer.
10. Put combination labels on a steering wheel and a steering shaft.
11. Using a stripper, remove a steering wheel from grooves of a steering shaft.
12. At removal of a steering wheel pass an electrocontrol run a radio receiver through an opening of a steering shaft.
13. Establish a steering wheel on a shlitsa of a steering shaft and pass through an opening of a steering wheel of a wire of management of a radio receiver.
14. Establish a washer, screw a nut of fastening of a steering wheel, having tightened it the demanded moment. Fix a nut from an otvorachivaniye a bending of a uvula of a washer.
15. Connect the electric socket of the switch of management of a radio receiver
16. Establish a safety airbag, previously having connected the electric socket. Fix a pillow screws.
17. Connect the accumulator.