Opel Vectra B

since 1995 of release

Repair and car operation



Vektr B. Opel
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
- 3. Engines
   - 3.1. Repair of the SOCH engine established in the car
      3.1.1. Introduction
      3.1.2. Technical characteristics
      3.1.3. Check of pressure of compression
      3.1.4. Top dead point (VMT) of the piston of the first cylinder
      3.1.5. Cover of a head of the block of cylinders
      3.1.6. Pulley of a cranked shaft
      3.1.7. Casings of a gear belt
      3.1.8. Gear belt
      3.1.9. Mechanism of a tension of a gear belt and pulleys
      3.1.10. Replacement of a sealing ring of a cam-shaft
      3.1.11. Cam-shaft and cam-shaft cases
      3.1.12. Hydraulic pushers
      3.1.13. Head of the block of cylinders
      3.1.14. Oil pallet
      3.1.15. Oil pump
      3.1.16. Drive flywheel / plate
      3.1.17. Replacement of sealing rings of a cranked shaft
      3.1.18. Suspension bracket of the power unit
   + 3.2. Repair of the DOCH engine established in the car
   + 3.3. Repair of the diesel engine of 1,7 l established in the car
   + 3.4. Repair of the diesel engine of 2,0 l established in the car
   + 3.5. Major maintenance of engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. Running gear
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions


5645d6d1

3.1.14. Oil pallet

Removal

PERFORMANCE ORDER
1. Remove a weight wire with akkumulyatora.agazhny office. Unscrew the holder of a spare wheel.
2. Lift a forward part of the car and fix on supports.
3. Merge engine oil. Establish a new washer on a drain stopper and screw up it into place.
4. Remove a forward exhaust pipe.
5. Disconnect the electric socket from the sensor of level of oil on the oil pallet.
Models without air conditioning (the steel stamped oil pallet)
6. Unscrew bolts and remove the bottom protective plate of a flywheel.
7. Gradually unscrew bolts of fastening of the oil pallet. Remove the pallet from the engine and take it from under the car. Remove laying of the oil pallet.
8. Remove and clear the mesh filter of a maslopriyemnik.
Models with air conditioning (the cast oil pallet)
9. Unscrew bolts of fastening of a ledge of the oil pallet to a transmission case.
10. Remove the rubber jams closing access to bolts of fastening of the oil pallet, unscrew bolts and remove the oil pallet.

Installation

Places of drawing of hermetic on the lower part of the block of cylinders of the engine


PERFORMANCE ORDER
Models with the steel stamped pallet
1. Remove all traces of dirt and oil from interfaced surfaces of the oil pallet and the block of cylinders.
2. If it is necessary, establish a new sealing ring of round section in the top part of a pipe of a maslopriyemnik and establish a maslopriyemnik. Before installation of bolts of fastening of a maslopriyemnik put on a carving of bolts the means interfering their unscrewing.
3. Establish new laying on the oil pallet and establish the oil pallet to the block of cylinders and fix bolts. A tightening of bolts of fastening of the pallet make from the center in diagonal sequence.
4. Establish a protective plate of a flywheel to a case of a transmission and fix bolts.
5. Establish a forward exhaust pipe and connect the electric socket to the sensor of level of oil in the oil pallet.
6. Lower the car and fill in in the engine fresh oil.
Models with the cast oil pallet
7. Remove all traces of dirt and oil from interfaced surfaces of the oil pallet and the block of cylinders.
8. Apply a thin film hermetic on interfaced surfaces of the block of cylinders and a back radical cover of the bearing.
9. Establish new laying on the oil pallet, and on a carving of bolts of fastening of the oil pallet put means against their unscrewing.
10. Establish the oil pallet and fix bolts. A tightening of bolts make from the center in diagonal sequence.
11. Screw in bolts of fastening of a ledge of the oil pallet to a transmission case.
12. Establish a forward exhaust pipe and connect the electric socket to the sensor of level of oil.
13. Lower the car and fill in in the engine fresh oil.