Opel Vectra B

since 1995 of release

Repair and car operation



Vektr B. Opel
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
- 5. Fuel system
   - 5.1. Fuel system of petrol engines
      5.1.1. Introduction
      5.1.2. Technical characteristics
      5.1.3. Air filter and inlet channels
      5.1.4. A control system in temperature of air submitted to the engine
      5.1.5. Accelerator cable
      5.1.6. Accelerator pedal
      5.1.7. Fuel
      + 5.1.8. System of injection of fuel
      5.1.9. Pressure removal in fuel system
      5.1.10. Fuel pump
      5.1.11. Fuel level sensor
      5.1.12. Fuel tank
      5.1.13. Throttle case
      5.1.14. Check of system of injection of fuel
      5.1.15. Elements of one-dot system of injection of fuel
      + 5.1.16. Elements of multipoint system of injection of fuel
      5.1.17. Inlet collector
      5.1.18. Final collector
      5.1.19. System of production of exhaust gases
   + 5.2. Fuel systems of the diesel engine
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. Running gear
+ 10. Body
+ 11. Electric equipment
+ 12. Main malfunctions


5645d6d1

5.1.17. Inlet collector

Removal and installation

PERFORMANCE ORDER
SOCH engines of 1,6 l
1. Remove pressure in fuel system and remove a weight wire from the accumulator.
2. Remove an auxiliary driving belt and merge cooling liquid from cooling system.
3. Remove a casing of the air filter and the inlet air channel.
4. Disconnect hoses from a throttle casing, unscrew screws and remove a casing from the top part of the case of a throttle.
5. Disconnect electric sockets from a potentiometer of a throttle, the engine of management of turns of idling, a fuel nozzle, the sensor of temperature of cooling liquid and the valve of system of repeated burning of exhaust gases.
6. Unscrew a bolt of fastening of the generator on the right side of a collector.
7. Unscrew connecting nuts and remove fuel hoses from the throttle case.
8. Remove a bracket of fastening and separate an accelerator torso from spherical sharnirny connection. Remove a cover of a cable of an accelerator from an arm.
9. Disconnect a vacuum hose and a hose of ventilation of a case from the throttle case.
10. Weaken a collar and remove a hose of cooling liquid from a back part of a collector.
11. Unscrew a connecting nut and remove a vacuum hose of the vacuum amplifier of brakes from a collector.
12. Check that all hoses are disconnected, and unscrew nuts of fastening of a collector.
13. Remove an inlet collector.
14. Installation is made in sequence, to removal, thus it is necessary to establish to return new laying of an inlet collector.
DOCH engines of 1,6 l
15. Unscrew bolts of fastening of a plastic arm of a plait of wires in a back part of an inlet collector.
16. Disconnect electric sockets from sensors of oxygen, the block of ignition, the valve of cleaning and other sockets on the left forward side of a collector. Unscrew a nut of fastening of the tire of grounding to a head of the block of cylinders and a collector.
17. Remove the catching valve паров fuels (it is specified by an arrow) since the left forward end of a collector and disconnect a valve hose from a collector.
18. Unscrew a connecting nut and remove a vacuum hose of the vacuum amplifier of brakes of a collector. Disconnect from a collector a vacuum hose and a hose of ventilation of a case of the engine.
19. Disconnect a vacuum hose from a pressure regulator.
20. Weaken collars and remove a hose connecting the case of throttles to the top section of a collector.
21. Unscrew bolts of fastening of the top section of a collector (are specified by shooters). Remove the top section of a collector and laying.
22. For removal of the bottom section of an inlet collector at first remove pressure in fuel system.
23. Unscrew connecting nuts and disconnect fuel hoses from the fuel highway.
24. Weaken the bottom bracket of fastening and remove a connecting part from the case of throttles.
25. Disconnect the electric socket from the sensor of a cranked shaft and release it from a collector.
26. Remove an accelerator torso from the case of throttles and disconnect electric sockets from the engine operating turns of idling, and a throttle potentiometer.
27. Unscrew bolts and remove the case of throttles.
28. Unscrew bolts from ledges of an arm of the case of throttles and remove an arm from a collector.
29. Remove an auxiliary driving belt and unscrew a bolt of fastening of the generator to the right side of a collector.
30. Unscrew nuts and remove the bottom section of a collector.
31. Installation is made in sequence, return to removal. Thus it is necessary to establish new laying of an inlet collector, to fill in cooling liquid in system of cooling and to adjust an accelerator torso.
L engines 1,8 and 2,0
32. Remove an auxiliary driving belt.
33. Remove pressure in fuel system and remove a weight wire from the accumulator.
34. Disconnect electric sockets from the sensor of temperature of air arriving in the engine and a measuring instrument of a stream of air.
35. Weaken a collar and remove a hose of ventilation of a case of the engine from a back part of a cover of a head of the block of cylinders.
36. Weaken collars and remove the inlet air channel from the air filter and the case of throttles.
37. Remove a bracket of fastening and separate an accelerator cable from spherical sharnirny connection of a cam of a throttle.
38. Unscrew bolts and remove an arm of a cable of an accelerator from the case of throttles.
39. Press hoses of supply of cooling liquid to a back part of the case of throttles, weaken collars and remove both hoses.
40. Remove electric sockets from a potentiometer of a throttle and the spherical engine of management of idling turns.
41. Note an arrangement and disconnect hoses from the case of throttles, then unscrew nuts and remove the case of throttles from an inlet collector.
42. Unscrew connecting nuts and remove fuel hoses from the fuel highway.
43. Disconnect electric sockets from the block of ignition, the valve of cleaning, the valve of a collector, the sensor of temperature of cooling liquid, the valve of repeated burning of exhaust gases and the oxygen sensor.
44. Release brackets of fastening and remove a casing with electric wires from a back part of a head of the block of cylinders. Disconnect electric sockets of the sensor of a cranked shaft and the detonation sensor.
45. Unscrew a connecting nut and remove a vacuum hose of the vacuum amplifier of brakes of a collector. Disconnect from a collector a vacuum hose and a hose of ventilation of a case of the engine. Disconnect a vacuum hose from a pressure regulator
46. Unscrew the top bolt of fastening of the generator on the right side of an inlet collector.
47. Unscrew bolts and remove an arm of support of the basis of a collector.
48. Unscrew nuts and remove a collector from the engine.
49. Installation is made in sequence, return to removal.