Vektr B. Opel + 1.1. Governing bodies and control devices + 2. Maintenance + 3. Engines + 4. Heating, ventilation + 5. Fuel system + 6. Systems of start, ignition + 7. Transmission + 8. Brake system + 9. Running gear + 10. Body - 11. Electric equipment - 11.1. Electric equipment 11.1.1. Introduction 11.1.2. Technical characteristics 11.1.3. Electric chains 11.1.4. Detection of not closed chain 11.1.5. Safety locks and relay 11.1.6. Switches 11.1.7. Bulbs of external lighting 11.1.8. Bulbs of internal lighting 11.1.9. Devices of external lighting 11.1.10. Adjustment of light of headlights 11.1.11. Combination of devices 11.1.12. Screen wiper levers 11.1.13. Screen wiper and draft engine 11.1.14. Engine of a screen wiper of a back door 11.1.15. Stekloomyvatel 11.1.16. Radio tape recorder 11.1.17. Loudspeakers 11.1.18. Safety cushion 11.1.19. Safety cushion elements + 11.2. Electroschemes + 12. Main malfunctions
|
FORWARD ILLUMINATION OF SALON
PERFORMANCE ORDER |
|
|
1. Being careful, a screw-driver remove from a ceiling a lamp of illumination of salon. |
|
2. Take a bulb from spring contacts. |
3. Establish a new bulb in sequence, return to removal. Check that the bulb is accurately fixed between spring contacts. If it is necessary, previously turn in contacts. |
|
BACK BULB OF ILLUMINATION OF SALON
PERFORMANCE ORDER |
|
1. Being careful and using a screw-driver, take from a ceiling a back bulb of illumination of salon. Take a bulb from spring contacts. |
2. Establish a new bulb in sequence, return to removal. Check that the bulb is accurately fixed between spring contacts. If it is necessary, previously turn in contacts. |
|
ILLUMINATION OF THE LUGGAGE COMPARTMENT
PERFORMANCE ORDER |
|
1. Being careful and using a screw-driver, remove a bulb of illumination of a luggage compartment. |
|
2. Take a bulb from spring contacts. |
3. Establish a new bulb in sequence, return to removal. Check that the bulb is accurately fixed between spring contacts. If it is necessary, previously turn in contacts. |
|
BULBS OF THE COMBINATION OF DEVICES
PERFORMANCE ORDER |
1. Remove a combination of devices. |
|
|
2. For removal of a bulb of an incandescence turn a cartridge of a bulb and take it from a combination of devices (in the photo at the left – removal of the small boss, on the right – big). |
|
3. Take a bulb from the boss, having pulled it on itself. Pay attention that some bulbs cannot be taken from cartridges. |
4. Establish a new bulb in sequence, return to removal. |
|
ILLUMINATION OF THE SWITCH OF LIGHTING
PERFORMANCE ORDER |
1. Remove the lighting switch. |
|
2. Using a screw-driver, turn a cartridge of a bulb and take it from a back part of the switch of lighting. |
3. Establish a new bulb in sequence, return to removal. |
|
BULBS OF THE MULTIPURPOSE BLOCK
PERFORMANCE ORDER |
1. Remove a combination of devices. |
|
|
2. Using flat-nose pliers, turn a cartridge with a bulb and take it from a back part of the multipurpose block. |
3. Establish a new bulb in sequence, return to removal. |
|
ILLUMINATION OF THE CONTROL PANEL BY THE HEATER
PERFORMANCE ORDER |
1. Remove the control panel a heater. |
|
2. Take the corresponding lamp, having pulled it on itself from the holder. |
3. Establish a new bulb in sequence, return to removal. |
|
|
|