Opel Vectra B

since 1995 of release

Repair and car operation



Vektr B. Opel
+ 1.1. Governing bodies and control devices
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. Running gear
+ 10. Body
- 11. Electric equipment
   - 11.1. Electric equipment
      11.1.1. Introduction
      11.1.2. Technical characteristics
      11.1.3. Electric chains
      11.1.4. Detection of not closed chain
      11.1.5. Safety locks and relay
      11.1.6. Switches
      11.1.7. Bulbs of external lighting
      11.1.8. Bulbs of internal lighting
      11.1.9. Devices of external lighting
      11.1.10. Adjustment of light of headlights
      11.1.11. Combination of devices
      11.1.12. Screen wiper levers
      11.1.13. Screen wiper and draft engine
      11.1.14. Engine of a screen wiper of a back door
      11.1.15. Stekloomyvatel
      11.1.16. Radio tape recorder
      11.1.17. Loudspeakers
      11.1.18. Safety cushion
      11.1.19. Safety cushion elements
   + 11.2. Electroschemes
+ 12. Main malfunctions





11.1.7. Bulbs of external lighting

GENERAL INFORMATION

Before replacement of a bulb of external lighting check the corresponding electric chain and a safety lock. Do not concern a glass flask of a lamp barehanded. The fingerprint evaporates and besieged on a reflector therefore lighting worsens. Surely replace the failed lamps with lamps of the same type. Spots arising on imprudence from touches wipe a pure bezvorsovy rag or alcohol.

HEADLIGHTS

PERFORMANCE ORDER
1. Open a cowl and remove a back cover from a headlight. Pay attention that an internal headlight for a passing beam, and an external headlight for a driving beam. At work on the left headlight it is necessary to remove the relay block from a forward part of the accumulator temporarily.
2. Remove the electric socket from a bulb of a headlight of a driving and passing beam.
3. Compress spring brackets of fastening of a bulb and move brackets aside.
4. Take a lamp from a headlight of a driving beam.
5. Release brackets of fastening of a bulb of a headlight of a passing beam.
6. Remove a bulb from a headlight of a passing beam.
7. Establish a new bulb in sequence, return to removal.

FORWARD DIMENSIONAL LAMP

PERFORMANCE ORDER
1. The lamp of a dimensional forward lamp is located in a headlight of a driving beam. Remove a back cover from a headlight.
2. Take a cartridge with a bulb of a dimensional lamp from a back part of a headlight.
3. Take a bulb from the boss.
4. Establish a new bulb in sequence, return to removal.

FORWARD INDEX OF TURNS

PERFORMANCE ORDER
1. Open a cowl and a screw-driver release the top bracket of fastening from outer side of a headlight.
2. Take the forward index of turns forward from grooves in a headlight.
3. Turn a cartridge with a bulb and take it from the forward index of turns.
4. Press and turn a bulb for extraction it from the boss.
5. Establish a new bulb in sequence, return to removal.

FORWARD FOG LIGHT

PERFORMANCE ORDER
1. Uncover a back part of the fog light located in a front bumper.
2. Disconnect the electric socket, weaken a bracket of fastening and take a bulb with a fog light.
3. Establish a new bulb in sequence, return to removal.

LATERAL REPEATER OF TURNS

PERFORMANCE ORDER
1. Using an edge of a thin screw-driver as the lever, take the lateral repeater of turns from an overlay of a forward wing.
2. Holding a cartridge of a bulb, turn the lateral repeater of turns and remove it from the boss.
3. Take from the boss a bulb, having pulled it on itself.
4. Establish a new bulb in sequence, return to removal.

BACK LAMPS

PERFORMANCE ORDER
1. Remove the furnish of a luggage compartment located opposite to back lamps.
2. Press fixing uvula in the middle of the holder of bulbs of a back lamp and take the holder of bulbs from a lamp.
3. Press and turn a bulb and take it from the holder of bulbs.
4. Establish a new bulb in sequence, return to removal.

LAMP OF ILLUMINATION OF REGISTRATION PLATE

PERFORMANCE ORDER
1. Open a luggage carrier or a back door, then insert an edge of a thin screw-driver vertically between the right edge of a lamp of illumination of registration plate and a rear bumper. Weaken a clamp and take a lamp of illumination of registration plate up from a bumper.
2. Press a bracket of fastening and remove a plafond from a lamp of illumination of registration plate.
3. Press and turn a bulb for removal it from the boss.
4. Installation of a new bulb is made in sequence, return to removal.

TOP STOPLIGHT

PERFORMANCE ORDER
1. Open a back door and remove an upholstery of furnish of a back part of salon.
2. Remove the caps closing screws.
3. Unscrew screws and remove a frame together with the top stoplight.
4. Separate from a frame a stoplight lamp.
5. Remove a casing from the holder of bulbs
6. Using a screw-driver, release clamps
7. Remove a strip with filament lamps from the holder.
8. Disconnect the electric socket and remove a strip with incandescence bulbs.
9. Installation is made in sequence, return to removal.