Opel Vectra B

since 1995 of release

Repair and car operation

Removal

PERFORMANCE ORDER

1. Remove a weight wire from the accumulator. 2. Lift a forward part of the car and fix on supports. 3. Merge engine oil, establish a new washer and establish a drain stopper in the oil pallet. Engines of 1,6 l 4. Remove a forward exhaust pipe. 5. Disconnect the electric socket from the sensor of level of oil. 6. Unscrew the bolts, fixing a ledge of the oil pallet to a transmission case. 7. For access to bolts of fastening of the oil pallet take the rubber jams closing bolts. 8. Gradually and consistently unscrew bolts of fastening of the oil pallet to the block of cylinders of the engine. Remove the oil pallet and laying. 9. Unscrew bolts and lift the receiver a maslopriyemnik with the mesh filter. Wash out the mesh filter. L engines 1,8 and 2,0 10. Disconnect the electric socket from the sensor of level of engine oil. 11. Unscrew bolts of fastening of the lower part of the oil pallet to the main block of the pallet and remove it together with laying. 12. For removal of the main block of the oil pallet from the engine remove the oil filter. 13. Remove a forward exhaust pipe. 14. Unscrew the bolts, fixing a ledge of the main block of the pallet to a transmission case. 15. Gradually unscrew bolts of fastening of the main block of the pallet to the block of cylinders. Remove the main block of the oil pallet together with laying. Prevention On some models it can be necessary to disconnect the right power shaft from a transmission for removal of the main block of the oil pallet. 16. Unscrew bolts and remove a maslopriyemny tube together with the mesh filter.

Installation

PERFORMANCE ORDER

1. Clear all traces of dirt and oil of interfaced surfaces of the oil pallet and the block of cylinders. Engines of 1,6 l 2. Establish a new sealing ring of round section on the top part of a pipe of a maslopriyemnik. Put on a carving of bolts means against unscrewing and screw a pipe of a maslopriyemnik on the oil pump. 3. Apply a thin film hermetic on a surface of the block of cylinders about the oil pump and a back main cover of the radical bearing (drawing places герментика are specified by stredka). 4. Establish new laying on the oil pallet. Put on a carving of bolts the means interfering unscrewing of bolts and screw up bolts of fastening of the oil pallet, working from the center in diagonal sequence. 5. Screw up bolts of fastening of a ledge of the oil pallet to a transmission case. 6. Establish a forward exhaust pipe and repeatedly connect the electric socket of the sensor of level of oil. 7. Lower the car on the earth and fill in engine oil in the engine. L engines 1,8 and 2,0 Prevention At installation of the oil pallet it is necessary to use new bolts. 8. Establish a new sealing ring of round section on the top part of a maslopriyemny pipe. Establish a maslopriyemny pipe on the oil pump and fix bolts. 9. Apply a thin film hermetic on the lower part of the block of cylinders in the field of installation of the oil pump and a back main radical cover of bearings. 10. Establish new laying on the main block of the oil pallet and on a carving of fastening of bolts of the oil pallet put the means interfering their unscrewing. 11. Establish the main block of the oil pallet on the block of cylinders and fix bolts, tightening them from the center in diagonal sequence. 12. Fix bolts a ledge of the main block of the oil pallet to a transmission case. 13. Establish a forward exhaust pipe and where it is necessary, connect a power shaft to a transmission. 14. Check that interfaced surfaces of the main block of the pallet and the bottom pallet pure and dry. Establish the bottom oil pallet with new laying on the main block of the oil pallet and fix it new bolts. 15. Establish the new oil filter and connect the electric socket to the sensor of level of oil. 16. Lower the car and fill in engine oil in the engine.